Відео

Great. Thank you. I already had to do this once, about ten years ago. My 2hp crapped out today. It will work on 120 but not 240v. I bought a new pump that should arrive tomorrow. Any idea why a pump would work on 120 but not 240v? The power in is 240 confirmed, 120 per leg.. capacitor is fine at 25uf, The only thing that was out of spec were the ohms between the windings (I think). I used the 3 leads to the capacitor and assumed each wire is one of the windings. I got something like 3.1, 4.2 and the third should be 7.3, but was only 6.3 or so (if that makes sense. I’m talking about between the pairs of windings. Anyway, it would not run at all on 240. No noise, no buzz no nothing. I switched it over to 120 by moving a jumper on the power inlet, made a cord with spade connections, plugged it into 120 outlet and it ran fine. I’m stumped. Any ideas? Sorry for the long post and thanks for the video. It was helpful.

HI I have old lawn boy lawn mower it runs when i try to put air cover back it will stop working .move the cover it will keep running

i just inherited an entire lot of this brand, blower hand trimmer and the wt3100 trimer you have. I have to replace the fuel lines but I'm a weee lost on which port the fuel line is on the carb and the starter line for the starter bubble fuel?

Great video

Thanks for posting. I now have auxiliary!

Hi, the pilot is on, I'm trying to close it to off - but ''wheel'' will only turn to the on position. Any suggestion for me? Thanks

dude, hold the camera steady.

There's a gasket? Any way mine starts, idles badly but won't rev up? How does the governor work? My motor has run for 19 years without problem, but i moved to Europe and the removals company flipped the mower so that oil got everywhere.

Wow thanks, exactly my problem

the problem that I have is that keeps beeping sharp and panel is blinking. it does cool

bonne video! j’ai apris plein de truc! j’aurais aimé voir comment reparer le petit tuyau qui donne le flow. le mien a lchaet coté sensor

Dommage la qualité de l'image et un peu trouble

Loosen that handle bolt halfway and hit it with a rubber mallet. Easy. Those handle nuts are manufactured like that purposefully: the older iteration that was solid brass caused issues. Installers would overtighten them and crush the inner shaft, damaging the light in the process. Imagine how much damage one overzealous PD installer could do in a day.

@QuaabQueb, awesome video dude. My buddy has a similar unit (Hayward Heatmaster) He didn't properly store it during the winter and the cpvc split. Does the whole coil have to be replaced? Worth saving?

Thanks for the fix. This was exactly my same scenario. I'm back in action now.

👋Hi I won't to know the diagram is like this and can I use any cable USB And Tkans:- * Green pin 1 * Black pin 2 * Red pin 3 * White pin 4

Great video👍🏾

😂 7 herbs and spices. Thanks for the review. Won't be buying it

Very helpful thanx!!

No luck, unfortunately he does not show the actual sticker and reading below one man suggested that there is a letter after the 5 numbers. None of that on my 2010. So i spent an easy 40 minutes trying this over and over. Freakin waste of time. Note, if it sounds too easy, have doubts...

Exactly the information I needed, thanks!!!! 👍

MAGA no other words !

But where does the carb spring go?

So duct tape was there to stop squeaking?

I fixed this issue on a mower by double gasketing it. I used a new paper one and then I made another by hand with cerial box cardboard and that was the second gasket. Worked great!

Where does the power come in from, and where does it go to

Nice.

In those last shots where you installed the nozzle on, you definitely pinched that hose. You can see the green pinched inside the clamp. That will leak in time.

Nice red wire on the nuetral Awful

Great video! I learned a lot about how the primer works. Is there not a low speed jet and a high-speed jet in these type carburetors. I have thoroughly cleaned my carburetor but it will only run with my hand over the air inlet. Like maybe a vacuum leak behind the carburetor but it's got a decent ring gasket on the tube. Runs great on starting fluid. Any thoughts? Thank you.

I still don't see it

How do you print the bracket template off there website I need to drill my bracket holes?

Would this work for a rubber garden hose? I have a Craftsman 50 foot garden hose, and the connector side for the sprayer came completely off. I am trying to find ways to repair it without purchasing a new hose

I have the same heater and it will shut off after around 3 minutes and it trips the breaker on my panel. I took it apart and nothing looked bad, can you provide any help? Thanks

Plant brûlée 😂😂😂

I think this was a great video. I appreciate seeing the problems and mistakes that could be made and how. To avoid them. I also appreciate the positive comments.

Thanks

Great vid thanks

A heater on your patio is the biggest waste of money I've ever seen. Go inside if you're cold or light a Camp Fire that's ridiculous right there.

Thanks for the video, step by step worked great. Sliding the smaller 7/16 worked great without having to remove anything. 30min including electrical

Its what.. the middle of summer. Whos using the heater 😂 it will be bugged up by winter and need cleaning anyway then.

Heat gun, hairdryer?

Did this and it still don't work

Is this AI?

Or just get a gas engineer that knows what he’s doing. A gas patio heater is just another gas appliance that you shouldn’t mess with!!!!

Cheers buddy 👍

replace carburetor every year is just $10 on amazon, issue solved…

For 1600 bucks, I’m buying a 300 dollar pump and taking a stab at it! Local pool store quoted me 1600. Nope…

Thanks for the video it was very informative. My question is I would like to run my Sum 4 with a variable speed water pump, but the water pressure switch is triggering a “low flow” error and won’t engage the heat. I’m thinking of replacing it by a digital programmable water pressure switch which would allow me to program a pressure range for it to close and engage the heat. Obviously it can’t be too low ‘cause I don’t it to overheat, but what do you think? Or do you have any suggestions?

It’s a scam